Granite edgeboot device firmware 0.5.1-braavos

Release Notes:

• Introduced a new commit & confirm feature that allows users to test configuration changes (like Ethernet settings) and automatically revert to the previous setup if not confirmed within 10 minutes, helping prevent downtime from unintended network changes
• Optimized device logging behavior that will increase efficiency and lower LTE usage consumption by over 80%
• Separated OS and app code versioning so each can be updated independently, allowing faster releases, improved stability, and greater flexibility
• Fixed an issue where AI mode did not detect profile changes, preventing tickets from opening when Ethernet interfaces went down while LTE remained active.
• Fixed an issue where health check pings only used available interfaces instead of testing all configured Ethernet interfaces
• Fixed an issue where system services could lose connection to the LED controller 

We recommend updating your devices to 0.5.1-braavos for optimal performance and improved reliability.

For eligible devices, a banner will appear as shown below. Click "Apply latest firmware" and you’re all set:

Granite edgebootPro device firmware 1.2.1-edge-pro

Important: The device will reboot twice during the upgrade process (up to 15 minutes). Do not disconnect power during this time, as interruption may permanently damage the device.

Release Notes:

• Introduced a new commit & confirm feature that allows users to test configuration changes (like Ethernet settings) and automatically revert to the previous setup if not confirmed within 10 minutes, helping prevent downtime from unintended network changes
• Optimized health checks and polling behavior that will increase efficiency and lower LTE usage consumption by ~80%
• Introduced multi-LAN functionality which allows edgebootPro to function with wireless as the primary uplink and both ethernet ports configurable as LAN
• Enhanced the provisioning process to disable 2G connections on Telit modems, improving network performance and reliability in areas where T-Mobile still operates 2G service
• Enhanced console management with port status indicators (In-Use/Available), customizable port labels, and SSH connectivity for devices on the local LAN
• Enhanced MQTT stability to prevent message delivery delays and connection interruptions
• Enhanced boot reliability to maintain consistent USB serial port assignments across reboots
• Fixed an issue where AI mode did not generate tickets in scenarios where Ethernet interface(s) were not specified within the Profile
• Fixed an issue where health check pings only used available interfaces instead of testing all configured Ethernet interfaces
• Fixed an issue where system services could lose connection to the LED controller
• Improved log file management and storage reliability 

We recommend updating your devices to 1.2.1–edge-pro for optimal performance and improved reliability.

For eligible devices, a banner will appear as shown below. Click "Apply latest firmware" and you’re all set:

Granite edgebootPro device firmware 1.1.3-edge-pro

Release Notes:

• Fixed an issue where bootloader messages from the outbound console port could interfere with connected network devices during boot
  • Important: The device will reboot twice during the upgrade process (up to 15 minutes). Do not disconnect power during this time, as interruption may permanently damage the device.

We recommend updating your devices to 1.1.3–edge-pro for optimal performance and improved reliability.

For eligible devices, a banner will appear as shown below. Click "Apply latest firmware" and you’re all set:

Check out what's new in the latest edgeboot portal release: 

feature Seamless Single Sign-On We've integrated with Okta so your edgeboot and G360 accounts now share the same login credentials—making it easier to switch between platforms without managing multiple passwords. 

improvement Enhanced Device Groups Capabilities

• Label what's connected to each port across all your devices at once in the Connected device info tab.
• Configure IP settings in bulk through the new Configurations tab.
• See at a glance which tasks completed successfully for each device in the Finished tasks tab.
• Navigate faster with improved quick links and icons.

feature Dual WAN Monitoring & Control For customers with dual wired connections, you can now monitor each Ethernet interface independently and configure automatic actions—like rebooting devices at the AC power port level—based on which connection needs attention.

feature Multi-LAN for Wireless-Primary Deployments Using edgebootPro with LTE as your primary connection? You can now configure both ETH0 and ETH1 as LAN ports—perfect for unmanned kiosks, ATMs, and vending machines that don't have wired internet available.

improvement Automatic SIM Activation SIM cards now activate automatically during device provisioning, eliminating manual activation steps.

improvement Automatic Site Syncing Sites now sync automatically in edgeboot.io, eliminating the need to manually sync before claiming devices through the portal.

improvement Smarter LTE Signal Monitoring We've refined how we detect LTE connectivity issues. You'll now see a clear "weak signal" warning banner when your LTE connection is having problems, without being overwhelmed by constant online/offline notifications. 

fix Fixed an issue where ETH0 was incorrectly locked as LAN on some devices.

Granite edgebootPro device firmware 1.1.2-edge-pro

Release Notes:

• Improved failover reliability by resolving occasional routing failures when switching between WAN connections.

We recommend updating your devices to 1.1.2–edge-pro for optimal performance and improved reliability.

For eligible devices, a banner will appear as shown below. Click "Apply latest firmware" and you’re all set:

Granite edgeboot device firmware 0.4.2-braavos

Release Notes:

fix Custom probe target value mismatches result in device status sync issues. This patch resolves value conflicts.

Granite edgeboot device firmware 0.4.1-braavos

Release Notes:

fix Rollback AI reboot service safeguards. Logic undergoing improvement prior to re-release.

Check out what's new in the latest edgeboot portal release:

feature Device Groups make it easier than ever to manage devices with similar configurations. Initial features include scheduling tasks at the group level and updating connected device info. The next release includes managing firmware, adjusting Ethernet interface settings, and applying Profiles. Get started today by adding devices to groups and easily manage large quantities of devices in the future!

feature Configure independent AI actions when monitoring dual WAN connections, specific to the Ethernet interface experiencing issues:

feature User-defined probe targets allow for customized Advanced Monitoring telemetry data to be captured and rendered in-app:

feature edgeboot is now certified for Granite's Multicarrier SIM. Devices with this SIM can connect to any major LTE provider network depending on best signal strength availability.

feature View, refresh, and clear ARP entries within Interface settings for devices with firmware 0.3.7-braavos or 1.0.7-edge-pro or later:

feature CSQ values are reported in addition to RSSI - simply toggle between RSSI & CSQ values under My Devices.

improvement Device events consolidation & improved formatting. Quicky understand when AI actions resolve or do not resolve connectivity.

improvement Custom sorting options for Scheduled Tasks and improved handling for offline devices.

improvement Easily identify AC port connection status via the built-in indicator:

feature Custom failover settings for edgebootPro - if there is already a failover device upstream, the auto-failover setting in the edgebootPro can be disabled to avoid failover conflicts.

feature Console session enhancements: a larger playground to work in and general font, cursor, and spacing enhancements.

Granite edgeboot device firmware 0.4.0-braavos

Release Notes:

• Allow user-defined probe targets for customized Advanced Monitoring telemetry
• Add graceful reboot option to serial console menu to perform remote system reboot without affecting devices plugged into edgeboot - simply press 0 to initiate a system reboot from the main console menu:

• AI mode logic enhancements for independent actions based on specific ethernet interfaces (ideal for monitoring two wired WAN connections)
• Enable USB-Serial driver for CH340/341 chipsets to support more USB serial devices
• Improve modem info collection by switching from AT to native commands
• Improve device logging and tune non-critical error messages
• Add safeguards to AI reboot service to prevent excessive reboots
• Implement additional performance monitoring for CPU and memory usage
• Adjust modem watchdog timers to allow for clean initialization across various LTE providers
  

We recommend updating your devices to 0.4.0-braavos for optimal performance and improved reliability. For eligible devices, a banner will appear as shown below. Click "Apply latest firmware" and you’re all set:

For best possible performance, security, and feature compatibility, we are sunsetting support for older firmware versions on edgeboot and edgebootPro devices.

End of Support Effective: July 31, 2025

The following firmware cutoffs will apply:

• edgeboot:
  ❌ All versions older than 0.4.0-braavos will no longer be supported.
• edgebootPro:
  ❌ All versions older than 1.1.0-edge-pro will no longer be supported.

Apply updates in-app or contact your account rep for bulk update options.